High resolution non-contact optical incremental encoder
High accuracy linear guide and carriage system with caged balls
Long life performance guaranteed
XY configuration has ≤5 arcsec orthogonality
Can be applied to industry applications like: laser cutting, scribing, drilling, marking
Linear stage is protected from dust and spray
All measurement reports are included by default
Direct Drive Linear Translation Stage of series 8MTL220 are based on 3 phase ironless linear brushless servo motor technology. Direct drive technology allow user to reach zero backlash motion with high accuracy, repeatability and low friction.
Linear non-contact optical encoder as a feedback system guarantees direct control of position with sub-nanometer resolution of motion.
Naturally aged aluminum alloy guaranties high temperature stability, softness of 8MTL220 instruments and excellent long period kinematics without drift of guide system. Small Special guiding system with caged recirculating ball ensure long last precision of stage.
Translation stages of series 8MTL220 can be prepared for clean rooms and vacuum up to 10-3 Torr with small changes. For higher vacuum please contact Standa support. Additional requirement of cleanliness could be requested separately.
Motorized translation stage can be easily connected to standard imperial/metric optical table directly. XY scanning stages can be directly assembled without using any connecting plates. For extreme orthogonality please contact Standa separately.
Motion control of 8MTL220 series translation stages is available with Standa or ACS motion Controllers & Drivers in exposed or housed configurations.
For industry applications 8MTL220 stages can be supplied mounted on standard optical table or extremely flat granite plate fully sealed from spray and dust to ensure performance of kinematic pairs.
Specifications
Model
8MTL220-400-LEn1
8MTL220-600-LEn1
Kinematics & Feedback information
Travel Range, mm
400
600
Encoder Type
Optical
Encoder Model
LEN1
Encoder Resolution
Any of the range:
25 nm to 5 µm
(on demand)
Encoder Interface
Differential RS422
Internal Multiplier
YES
Multiplication factor 1)
4-200 (on demand)
Encoder Grating Period, µm
20
Reference Mark (Index)
Yes
Absolute Accuracy 2)
Before Calibration, µm
±10
±12
After Calibration, µm
±1
±1
Uni-Directional Repeatability, µm
N/A
Bi-Directional Repeatability (peak to peak) 2), µm
±0.5
Bi-Directional Repeatability (RMS) 2), µm
±0.26
Pitch 3), µrad / arcsec
±30 / ±6.20
Yaw 3), µrad / arcsec
±30 / ±6.20
Roll, µrad / arcsec
N/A
Maximum Velocity (with load 4kg) 4), mm/s
<2000
Maximum Acceleration (with load 4kg) 5), mm/s2
<20000
Limits Switches Type (Safety)
Optical (Optrons)
Limit Switch Polarity (Safety)
Pushed is closed
Limit Switch Voltage, V
5…24
Load, Guiding & Transmission Information
Design Type
Linear Motor Stage
Linear Motor Model
LM4
Linear Motor Design Type
Ironless BLDC motor
Maximum Bus Voltage, VDC
>300
Load Capacity (Centrally Placed) 6)
Horizontal, kg
100
Vertical, kg
N/A
Moving Mass 7), kg
9.5
Guiding System
Recirculating linear rails and carriages units with caged balls
Material & Environment Conditions
Housing Material
Aluminum Alloy
Housing Coating (Finish)
Black Anodizing
Environment Pressure
Normal Atmosphere
Operating Temperature, °C
20±2
Control, Communication and Cabling
Recommended Controllers 8)
ACS Products Line or 8SMC5-USB series
Recommended Drivers 8)
ACS Products Line or 8SMC5-USB series
Recommended Power Supply 9)
2 phase / 3 phase source
Recommended Communication Interface 12)
EtherCAT / RS232 / USB / TCP-IP
Cable Length, m
2 (other by request)
Differential Outputs 10)
On request
Accessories Information
Base Plate for Mechanical Interface
Not required
XY Stack
Directly
Z Configuration
Not available (choose from other Standa stages series)
In the video below 4-axis system is demonstrated, where direct drive linear translation stage 8MTL220-400-LEn1 (400 mm stroke) is used as a base linear positioner for X-axis motion.